Product Set Ups

HOW DO I CONNECT UP MY JCM900 SERIES HEAD AND A SINGLE MONO/STEREO 1960 SERIES CAB?

First, make sure the amplifier is switched off, then set the 1960 to Mono (Fig. 5.1) and connect a speaker cable to either of the JCM900′s Parallel loudspeaker outputs (Fig. 5.2). Connect the other end of the speaker cable to the 1960′s 16 Ohm input (Fig. 5.3). Now set the JCM900′s impedance selector to 16 Ohms (Fig. 5.4).

5-1

5.1

5-2

5.2

5-3

5.3

5-4

5.4

 

How do I connect up my JCM900 Series Head and two Mono/Stereo 1960 Series Cab?

First, make sure the amplifier is switched off, then set both cabinets to Mono (Fig. 6.1) and connect a speaker cable to either of the JCM900′s Parallel loudspeaker outputs (Fig. 6.2). Connect the other end of the speaker cable to the first 1960′s 16 Ohm input (Fig. 6.3). Now connect a second speaker cable to the JCM900′s remaining parallel loudspeaker output (Fig. 6.4). Connect the other end of this cable to the second 1960′s 16 Ohm input (Fig. 6.5). Lastly set the JCM900′s impedance selector to 8 Ohms (Fig. 6.6).

What is the most common way to connect up my DSL/TSL Series head and a single Mono/Stereo 1960 Series cab?

First, make sure the amplifier is switched off, then set the 1960 to Mono (Fig. 7.1) and connect a speaker cable to the TSL/DSL’s 16 Ohm Only loudspeaker output (Fig. 7.2). Connect the other end of the speaker cable to the 1960′s 16 Ohm input (Fig. 7.3). The position of the TSL/DSL rear panel 4/8 Ohm impedance selector does not matter in this scenario.

 

Is there an alternative way to connect up my DSL/TSL Series head and a single Mono/Stereo 1960 Series cab?

First, make sure the amplifier is switched off, then set the 1960 to Mono (Fig. 8.1) and connect a speaker cable to either of the TSL/DSL’s 4/8 Ohm Parallel loudspeaker outputs (Fig. 8.2). Connect the other end of the speaker cable to the 1960′s 4 Ohm input (Fig. 8.3). Set the TSL/DSL’s 4/8 Ohm impedance selector to 4 Ohms (Fig. 8.4).

8-2

8.2

 

How do I set up my TSL/DSL head and two Mono/Stereo 1960 Series cabs?

First, make sure the amplifier is switched off, then set both 1960 cabinets to Mono (Fig. 9.1) and connect a speaker cable to either of the TSL/DSL’s 4/8 Ohm Parallel loudspeaker outputs (Fig. 9.2). Connect the other end of the speaker cable to the firs 16 Ohm speaker input (Fig. 9.3). Connect a second speaker cable to the remaining TSL/DSL 4/8 Ohm Parallel loudspeaker output (Fig. 9.4). Then connect the other end of this cable to the second 1960′s 16 Ohm input (Fig. 9.5). Finally, set the TSL/DSL 4/8 Ohm impedance selector to 8 Ohms (Fig. 9.6).

9-2

9.2

9-4

9.4

 

How do set up my TSL60 head and a single Mono/Stereo 1960 Series cabinet?

First make sure the amplifier is switched off, then set the 1960 to Mono (Fig. 10.1) and connect a speaker cable to either of the TSL’s Parallel loudspeaker outputs (Fig. 10.2). Connect the other end of the speaker cable to the 1960′s 16 Ohm input socket (Fig. 10.3). Now set the TSL60′s 8/16 Ohm impedance selector to 16 Ohms (Fig. 10.4).

 

How do I set up my TSL60 head with two Mono/Stereo 1960 Series cabinets?

First insure that the amplifier is switched off, then set both cabs to Mono (Fig. 11.1) and connect a speaker cable to either of the TSL’s Parallel loudspeaker outputs (Fig. 11.2). Connect the other end of the speaker cable to the first cabinet’s 16 Ohm input socket (Fig. 11.3). Plug a second speaker cable into the remaining Parallel loudspeaker output on the head unit (Fig. 11.4) and insert the other end into the 16 Ohm input socket on the second cabinet (Fig. 11.5). Finally, set the TSL60′s 8/16 Ohm impedance selector to 8 Ohms (Fig. 11.6).

11-6

11.6

 

How do I set up my TSL60 head and a single Mono 1960 Series cabinet?

Firstly make sure the amplifier is switched off, and then connect a speaker cable to either of the TSL60′s Parallel loudspeaker outputs (Fig. 12.1). Plug the other end of the speaker cable into the Mono 1960′s 16 Ohm input (Fig. 12.2) and set the head’s 8/16 impedance selector to 16 Ohms (Fig. 12.3).

12-2

12.2

12-3

12.3

 

How do I set up my TSL60 head and two Mono 1960 Series cabinets?

Insure the amplifier is turned off, and then connect a speaker cable to either of the TSL60′s Parallel loudspeaker output (Fig. 13.1). Next, connect the other end of the speaker cable to the first Mono 16 Ohm speaker input (Fig. 13.2) and repeat this process with a second speaker cable, connecting the remaining output and input sockets (Fig. 13.3 & 13.4). Now set the TSL60′s 8/16 Ohm impedance selector to 8 Ohms (Fig. 13.5).

13-2

13.2

13-4

13.4

13-5

13.5

 

What is the most common way to connect up my 'Vintage Style'/Vintage Re-issue/Handwired head and a single Mono/Stereo 1960 Series cab?

First, make sure the amplifier is switched off, then set the 1960 to Mono (Fig. 14.1) and connect a speaker cable to the head’s 16 Ohm Only loudspeaker outputs (Fig. 14.2). Connect the other end of the speaker cable to the 1960′s 16 Ohm input (Fig. 14.3). Set the head’s impedance selector to 16 Ohms (Fig. 14.4).

 

Is there an alternative way to connect up my 'Vintage Style'/Vintage Re-issue/Handwired head and a single Mono/Stereo 1960 Series cab?

First, make sure the amplifier is switched off, then set the 1960 to Mono (Fig. 15.1) and connect a speaker cable to either of the head’s Parallel loudspeaker outputs (Fig. 15.2). Connect the other end of the speaker cable to the 1960′s 4 Ohm input (Fig. 15.3). Set the head’s impedance selector to 4 Ohms (Fig. 15.4).

 

How do I set up my 'Vintage Style'/Vintage Re-issue/Handwired head and two Mono/Stereo 1960 Series cabs?

First, make sure the amplifier is switched off, then set both 1960 cabinets to Mono (Fig. 16.1) and connect a speaker cable to either of the head’s Parallel loudspeaker outputs (Fig. 16.2). Connect the other end of the speaker cable to the first 1960′s 16 Ohm input (Fig. 16.3). Connect a second speaker cable to the head’s remaining parallel loudspeaker output (Fig. 16.4). Then connect the other end of this cable to the second of the 1960′s 16 Ohm input (Fig. 16.5). Finally, set the head’s impedance selector to 8 Ohms (Fig. 16.6).

16-6

16.6